Posts Tagged ‘erase’
In continuation of my article: Data Erasing for your own Protection I got into a discussion about other ways to protect you data from law enforcement.
I was told by a former law enforcement member that after the crime scene has been secured that the the computer tech checks the computer is functional and then has the equivalent of a mover ship the computer, like a box, to the computer lab. The issue with this being that a mercury switch and power source could be used to zap the computer with the needed Gauss to erase/destroy the hard disk.
Another method would be to use a RAM Disk, whether this is a physical or virtual RAM Disk. The first has the advantage that in the case of a brownout the data is saved for X hours, although this could be a disadvantage too, another disadvantage is that you may have a memory limit which is imposed by the hardware. The advantage over the physical RAM disk is that a higher amount of memory can be allocated, although you don’t get the protection from brownouts.
Important to also remember is that there is also a data remanence with data in RAM, which also should to be mitigated. This may be possible by passing an electric charge over the memory to erase them, although I have yet to find relevant references.
A third method may be by raising the temperature of the hard disk to above the Curie Point, which with effect the magnetics of the disk. I will need to investigate this more too.
Embedding part of the computer in epoxy still applies to all the above.
- Gigabyte I-RAM DDR PCI Virtual RAM Disk Drive SATA W/ Backup Battery – backup power lasts ~16 hours and it supports 4Gb RAM.
- Data remanence: Data in RAM
- Curie Point
Image source: Michiel2005
I’ll describe the problem I think that you have: You have data stored on computers which you don’t want the police or the governments to have, something that cryptography can not protect, as XKCD so eloquently puts in the cartoon Security below. You are not the only one: internet companies; financial institutions; churches; organizations working for freedom; lawyers; criminals and innocent individuals all need to protect themselves.
It’s possible to use something like Darik’s Boot and Nuke (DBAN) which is a self-contained boot disk that securely wipes the hard disks of most computers, however this takes time sometimes a number of hours and requires human interaction. Time that may not be available if the long arm of the law comes down on you like a ton of bricks. And it can even be the case that the power is shut off before the computer is secured, the police do this to keep the data on the computer secured for the investigation. So I thought about what would be needed to magnetically erase the hard disk.
Secondly I read that degaussing can cause permanent irreversible damage to hard drives which means they are not reusable. Unlike tapes the mechanism to read the magnetic track is part of the device and is also magnetic. So don’t expect to be able to use the disk after you have tested the electromagnet.
Thirdly the magnetic induction (also referred to as magnetic flux density or saturation flux density) needed to correctly erase some hard disk can be from 6000 – 7000 gauss (0.6 – 0.7 tesla), an NSA approved degausser puts out 22000 gauss (2.2 telsa). From some sources I learned that mostly the core of electromagnets is made from a magnetic material – power ferrite – which has a magnetic flux density of under 4000 gauss, this wouldn’t be enough. A different material would be needed for the core of the electromagnet. I discovered that MPP (molypermalloy powder) material has a magnetic flux density of 7000 gauss, which is what is needed for this PoC. Iron powder and high-flux can yield 10000 and 15000 gauss respectively.
Fourth you need thick copper wire wound round the core, this is called a solenoid. This creates the B-field which is the magnetic field which will erase the hard disk, using a gauss or EMF meter it is possible to measure the magnetic flux density in gauss or telsa produced by your electromagnet and experiment with getting the level to 6000-7000 gauss.
Fifthly you need an Uninterruptible Power Supply (UPS), this will ensure that when the power is switched off that the electromagnet is powered up to erase the hard disk.
Lastly you need to install your electromagnet round your hard disk, hook up the UPS and fill the computer with epoxy so it cannot be taken apart by the police. Let’s just hope you don’t have a brownout.
Sadly this method will not work for solid state disks, although you can possibly attach squibs using a similar setup. That may be something for a future article.
- Degaussing : Irreversible damage to some media types
- I am creating an electromagnet for my school’s science fair project. Does the shape of the iron core make a difference? [...]
Image source: Michiel2005